Wednesday, January 13, 2010
The V4X is probably the cheapest standalone that does not break the bank and has more function the piggyback thats almost the same price. This is because other than controlling the fuel and ignition it is also capable of controlling the Toyota VVT-I. Where most piggyback and standalone only offer VTEC control.
Wolf V4X
Normal Price: $2,200.00
Normal Price: $2,200.00
Promotion Price: $1,800.00 (PROMOTION END ON 31ST JAN 2010)
Description:The Wolf V4X is a very cost effective, light-weight and compact engine management system.
Inputs:
Engine Speed
Vehicle Speed
Engine Temperature
Air Temperature
Throttle Position
Internal MAP Sensor (Rated to 30 PSI)
Outputs:
4 Injector Drivers - (Minimum Injector Impedance 0.8 Ohms per output)4 Ignition Outputs
Fuel Pump Control
Boost Control
Stepper Motor Idle Speed Control
PWM Idle Speed Control
2 Switched Low Side Auxiliary Outputs
4 Switched High Side / Low Side Auxiliary Outputs
Note: This kit is a universal (wire-in) kit. You can check out our range of Plugin V4X ECU's to find an ECU that plugs straight into your vehicles original harness. No Wiring!
Normal Price: $2,800.00
Promotion Price: $2,400.00 (PROMOTION END ON 31ST JAN 2010)
Description:
8 Smart, Full sequential Injector outputs, driving 1-32 injectors, including high flow, low impedance injectors down to 0.5ohms per output pin.The V500 injector driver system reports live status of all injector channels including peak and hold reached times, injector current, short, weak and open circuits.
8 Full sequential Ignition outputs, driving 1-8 ignition coil packs in sequential, banked, single, rotary or inverted modes.
Latest 3D graphing, live dashboards and Datalogging software.
Advanced high-detail Fuel, Ignition and Control mapping systems, 2048 points at 125rpm steps with Easy Tuning modes.
Dual Memory system, Power/Economy, Petrol/Gas modes and more.
Control Functions:
16 General Purpose Output (GPO) functions supporting Auxiliary Outputs, with windowed switching
6 MultiController Output (MCO) functions, supporting 3D and 2D multi-axis tables for mapped linear control of any extra outputs desired, including PWM, solenoid position and trim control of internal ECU parameters
GPO and MCO functions can support VTEC/VVT, NOS, Water Spray, Stepper Motor, Emissions Control, Idle Up, Warning Lights, and any other additional devices required.
Wide-Band Air-Fuel-Ratio (Lambda)
Closed Loop Control
Idle Speed Control
Stepper Motor Control
Turbo Boost/Wastegate Control
Turbo Timer support
Shift Light function, dedicated with up to 6 stages and flash point.
Dedicated Inputs:
13 Auxiliary Input pins available as many extra inputs
Camshaft, Crankshaft, Reference and Sync Trigger inputs, Hall Effect, Reluctor and Optical, user selectable
Internal MAP sensor up to 30psi boost (higher with external sensor)
External MAP or MAF Sensor
Throttle Position
Engine Temperature
Lambda/Oxygen Sensor, Dual Channel, Narrow Band or Wideband LSU4
Air Conditioning Request
Vehicle/Wheel Speed
Dedicated Outputs:
15 to 27 Auxiliary Output pins available as extra outputs (unused Injector and Ignition pins can be used)
8 Smart, Full sequential Injector outputs
8 Full sequential Ignition outputs
Fuel Pump
Thermo Fan
Idle Speed Control
Tacho Output
Turbo Timer
Sensor Inputs have full OEM-style diagnostics and error checking on each input, detecting out of range or faulty sensors, correcting them to a safe value, and reporting the fault via a flash-code system. Any errors logged can then be inspected by the Wolf V500 PC Software included.
Runs engines up to 16 cylinders with full rotary engine support and odd cylinder counts allowed.
Internal MAP sensor reads boost pressures up to 30psi.
Supports most existing sensors in the vehicle, saving wiring and installation time.
Latest 32 bit processor running at 40MHz with Dual Time Co-Processors, giving precise sequential delivery of fuel and ignition and supporting all other functions including high speed Datalogging with no performance loss.
Weighs only 500 grams and measures 126mm x 114mm x 39mm.Supplied with wiring harness, quick start guide and searchable installation manual.
8 Full sequential Ignition outputs, driving 1-8 ignition coil packs in sequential, banked, single, rotary or inverted modes.
Latest 3D graphing, live dashboards and Datalogging software.
Advanced high-detail Fuel, Ignition and Control mapping systems, 2048 points at 125rpm steps with Easy Tuning modes.
Dual Memory system, Power/Economy, Petrol/Gas modes and more.
Control Functions:
16 General Purpose Output (GPO) functions supporting Auxiliary Outputs, with windowed switching
6 MultiController Output (MCO) functions, supporting 3D and 2D multi-axis tables for mapped linear control of any extra outputs desired, including PWM, solenoid position and trim control of internal ECU parameters
GPO and MCO functions can support VTEC/VVT, NOS, Water Spray, Stepper Motor, Emissions Control, Idle Up, Warning Lights, and any other additional devices required.
Wide-Band Air-Fuel-Ratio (Lambda)
Closed Loop Control
Idle Speed Control
Stepper Motor Control
Turbo Boost/Wastegate Control
Turbo Timer support
Shift Light function, dedicated with up to 6 stages and flash point.
Dedicated Inputs:
13 Auxiliary Input pins available as many extra inputs
Camshaft, Crankshaft, Reference and Sync Trigger inputs, Hall Effect, Reluctor and Optical, user selectable
Internal MAP sensor up to 30psi boost (higher with external sensor)
External MAP or MAF Sensor
Throttle Position
Engine Temperature
Lambda/Oxygen Sensor, Dual Channel, Narrow Band or Wideband LSU4
Air Conditioning Request
Vehicle/Wheel Speed
Dedicated Outputs:
15 to 27 Auxiliary Output pins available as extra outputs (unused Injector and Ignition pins can be used)
8 Smart, Full sequential Injector outputs
8 Full sequential Ignition outputs
Fuel Pump
Thermo Fan
Idle Speed Control
Tacho Output
Turbo Timer
Sensor Inputs have full OEM-style diagnostics and error checking on each input, detecting out of range or faulty sensors, correcting them to a safe value, and reporting the fault via a flash-code system. Any errors logged can then be inspected by the Wolf V500 PC Software included.
Runs engines up to 16 cylinders with full rotary engine support and odd cylinder counts allowed.
Internal MAP sensor reads boost pressures up to 30psi.
Supports most existing sensors in the vehicle, saving wiring and installation time.
Latest 32 bit processor running at 40MHz with Dual Time Co-Processors, giving precise sequential delivery of fuel and ignition and supporting all other functions including high speed Datalogging with no performance loss.
Weighs only 500 grams and measures 126mm x 114mm x 39mm.Supplied with wiring harness, quick start guide and searchable installation manual.
Also available @ Sen Yeong are Tein(official distributor), OWS lubricants, Motul, Project Mu brake system etc
Subscribe to:
Posts (Atom)
